https://github.com/yrutschle/sslh

sslh accepts connections on specified ports, and forwards them further based on tests performed on the first data packet sent by the remote client.

Probes for HTTP, TLS/SSL (including SNI and ALPN), SSH, OpenVPN, tinc, XMPP, SOCKS5, are implemented, and any other protocol that can be tested using a regular expression, can be recognised. A typical use case is to allow serving several services on port 443 (e.g. to connect to SSH from inside a corporate firewall, which almost never block port 443) while still serving HTTPS on that port.

Hence sslh acts as a protocol demultiplexer, or a switchboard. With the SNI and ALPN probe, it makes a good front-end to a virtual host farm hosted behind a single IP address.

sslh has the bells and whistles expected from a mature daemon: privilege and capabilities dropping, inetd support, systemd support, transparent proxying, chroot, logging, IPv4 and IPv6, TCP and UDP, a fork-based, a select-based model, and yet another based on libev for larger installations.

Please refer to the install guide.

Please refer to the configuration guide.

Transparent proxying allows the target server to see the original client IP address, i.e. sslh becomes invisible.

This means services behind sslh (Apache, sshd and so on) will see the external IP and ports as if the external world connected directly to them. This simplifies IP-based access control (or makes it possible at all), and makes it possible to use IP-based banning tools such as fail2ban.

There are two methods. One uses additional virtual network interfaces. The principle and basic setup is described here, with further scenarios described there.

Another method uses iptable packet marking features, and is highly dependent on your network environment and infrastructure setup. There is no known generic approach, and if you do not find directions for your exact setup, you will probably need an extensive knowledge of network management and iptables setup".

It is described in its own document. In most cases, you will be better off following the first method.

How to use

docker run \
  --cap-add CAP_NET_RAW \
  --cap-add CAP_NET_BIND_SERVICE \
  --rm \
  -it \
  ghcr.io/yrutschle/sslh:latest \
  --foreground \
  --listen=0.0.0.0:443 \
  --ssh=hostname:22 \
  --tls=hostname:443

docker-compose example

version: "3"services:  sslh:    image: ghcr.io/yrutschle/sslh:latest
    hostname: sslh
    ports:
      - 443:443
    command: --foreground --listen=0.0.0.0:443 --tls=nginx:443 --openvpn=openvpn:1194
    depends_on:
      - nginx
      - openvpn

  nginx:    image: nginx

  openvpn:    image: openvpn

Transparent mode 1: using sslh container for networking

Note: For transparent mode to work, the sslh container must be able to reach your services via localhost

version: "3"services:  sslh:    build: https://github.com/yrutschle/sslh.git
    container_name: sslh
    environment:
      - TZ=${TZ}
    cap_add:
      - NET_ADMIN
      - NET_RAW
      - NET_BIND_SERVICE
    sysctls:
      - net.ipv4.conf.default.route_localnet=1
      - net.ipv4.conf.all.route_localnet=1
    command: --transparent --foreground --listen=0.0.0.0:443 --tls=localhost:8443 --openvpn=localhost:1194
    ports:
      - 443:443 #sslh

      - 80:80 #nginx
      - 8443:8443 #nginx

      - 1194:1194 #openvpn
    extra_hosts:
      - localbox:host-gateway
    restart: unless-stopped

  nginx:    image: nginx:latest
    .....
    network_mode: service:sslh #set nginx container to use sslh networking.
    # ^^^ This is required. This makes nginx reachable by sslh via localhost
  
  openvpn:    image: openvpn:latest
    .....
    network_mode: service:sslh #set openvpn container to use sslh networking

Transparent mode 2: using host networking

version: "3"services:  sslh:    build: https://github.com/yrutschle/sslh.git
    container_name: sslh
    environment:
      - TZ=${TZ}
    cap_add:
      - NET_ADMIN
      - NET_RAW
      - NET_BIND_SERVICE
    # must be set manually
    #sysctls:
    #  - net.ipv4.conf.default.route_localnet=1
    #  - net.ipv4.conf.all.route_localnet=1
    command: --transparent --foreground --listen=0.0.0.0:443 --tls=localhost:8443 --openvpn=localhost:1194
    network_mode: host
    restart: unless-stopped
  
  nginx:    image: nginx:latest
    .....
    ports:
      - 8443:8443 # bind to docker host on port 8443

  openvpn:    image: openvpn:latest
    .....
    ports:
      - 1194:1194 # bind to docker host on port 1194

推荐本站淘宝优惠价购买喜欢的宝贝:

本文链接：https://sg.hqyman.cn/post/9529.html 非本站原创文章欢迎转载，原创文章需保留本站地址！

打赏

微信支付宝扫一扫，打赏作者吧～

休息一下~~